The flashing blue light on your Labradar indicates the SD card is not compatible. It must be 32GB or less, SD or SDHC. Micro USB cards are not recommended. Do a FULL Format of the SD card using FAT 32 and try the card again.
How do I change the App from Metric to Standard measurements
Swipe the Labradar logo in the upper left corner to the right. A Settings menu will appear that permit changes on the Labradar and the mobile device.
How do I get to the Preferences Menu?
Press the top left button if you are in the Series View. If you are in the Armed View press and hold the Armed button for 2-3 seconds and you will be taken to the Series View. You can then press the Preferences Menu button.
If your in the armed view, press and hold the armed button for 2-3 seconds and the Series screen will be displayed. You can now press the New Series button and confirm your desire to start a new series.
Do you have any videos that show proper setup and operation?
Yes, we have several videos posted on our YouTube. Search YouTube with the keywords “Labradar Channel” or go to the link below.
https://www.youtube.com/channel/UCWLcaC5zBL-ZcdLZS9BRmKg
If your Labradar will not trigger it is because it is not armed (light orange) or it is not “feeling” the muzzle blast. Unless you have a muzzle brake on your weapon your muzzle should be even with the side of the unit. This applies to handguns and rifles. Keep the Trigger Level set at 1.
How do I use Labradar with 22 rimfire, Airguns or Suppressors?
Since there is very little muzzle blast pressure emitted from 22 rimfire, Airguns or suppressed firearms you may need to place Labradar approximately 3 inches in front of the muzzle and approximate 3 inches to the side. If your unit still will not trigger due to the low muzzle blast you can purchase the Air Gun Adapter to assist in triggering the radar.
LabRadar velocity measurements are based on Continuous Wave Doppler Radar and advanced Digital Signal Processing Technologies.
My radar triggers but I do not get a velocity reading.
When you get an error message that the projectile was not acquired it is usually due to poor alignment of the radar or muzzle blast debris interfering with the radar reflecting off of the bullet. To resolve this you can move your muzzle farther forward and farther to the side. Be sure to adjust the Projectile Offset distance when moving farther to the side. You can confirm your alignment by looking through a small diameter tube placed in the sighting notch.
Where should my muzzle be positioned?
Ideally you should place your muzzle even with the side of the unit and between the top and bottom corners. If you have a muzzle brake you should place it a few inches in front of the radar to prevent the direct muzzle blast from impacting the unit. Be sure to set your Projectile Offset to the correct distance in the preferences menu.
Can Labradar be placed downrange
Labradar is designed to set besides the shooter as it is triggered by the weapon muzzle blast. Currently it is not possible to trigger the radar at a downrange location.
Yes, LabRadar was designed for and is in compliance with the United States FCC Regulations, CE requirements and Canada requirements.
Can I use it at an Indoor Range?
Labradar will work in most indoor ranges. You will need at least 50 feet since the beam is quite small at those distances. It may not work if you are shooting in a tunnel or tube as the radar will be reflecting off of those surfaces.
Yes, unlike most light sensing chronographs LabRadar is not affected by these environmental conditions.
If you’re not in the center of the radar beam is the accuracy diminished?
No, but you will be able to track the bullet farther if your in the center of the beam.
Yes. LabRadar uses 6 AA type batteries. It can also be powered from an external USB power pack.
What range performance can one expect with LabRadar?
In general LabRadar will typically measure the velocity of a 7.62 mm projectile from muzzle up to 100 yards. After extensive testing of a variety of calibers you can expect to obtain velocities at these distances when in the Standard Power Mode. Low Power setting will have about 30% less tracking*.
- .177 Pellet – 30 yards;
- .177 BB – 30 yards;
- 22 LR – 60 yards;
- 223 – 60 yards;
- 270 – 70 yards;
- 308 – 80 to 100 yards;
- 9mm – 130 yards;
- 40 S&W – 130 yards;
- 45 ACP – 130 yards;
- 500 S&W – 130 yards;
- 12 gauge Slug – 90 yards;
- Paint Ball – 50 yards;
- Arrows – 50 yards;
* Since every bullet has a different profile your results may vary. In general, the larger the base (excluding the boat tail) the great the distance the projectile can be acquired.
One year from date of purchase.
Can the LabRadar be used with bows and crossbows?
Yes, when used in the Doppler mode the arrow acts as the trigger when it enters the radar beam. This is generally 6-10 feet downrange. It will continue to track the arrow for approximately 60 yards. When in the Trigger Mode an adapter can be used on the bow to communicate with LabRadar. The adapter will trigger the radar in the release of the arrow.